If You Think Your Vehicle Is Cool  Think Again!!Coat Your Vehicle With TSD-Heat Dispersant Coating.

Purchase A GFB Boost Controller AND A Blow Off Valve In A Single Purchase, Receive A 5% Discount .

Purchase A GFB Boost Controller, Blow Off Valve  AND  A Wastegate In A Single Purchase, Receive A 10% Discount.

The Discounts will be reflected in the shopping cart.

IMPROVE YOUR VEHICLE'S COOLING PERFORMANCE

Heat Dispersant Coating For Intercoolers, Radiators, Oil Coolers, etc

TSD Coated EVO

TSD Coated Intercooler

Improve Your Vehicle's Intercooler Cooling Efficiency Note the color white on the coated intercooler.

GFB Respons TMS Blow Off Valve

GFB Respons TMS T9000.

Endless Brake Pads

MX72 Brake Pads

UltraRacing Bars

Improve Your Vehicle's Handling With UltraRacing

About UltraRacing

MATERIAL SPECIFICATION & DESIGN

Every materials used are carefully selected to ensure the best performance and safety. The brackets are made of 4mm to 5mm steel plates, while the hollow steel tubes and oval tubes are of 1.2mm to 1.6mm thickness. These materials are selected to ensure the bars are rigid and strong to maintain constant geometry at all times, yet safe enough to crumble during an impact for safety reason

All raw materials has been made and tested with satisfactory result. 

 MILL / TEST CERTIFICATE (Chemical Composition) 

Specification - JIS 3101 SS 400  (Japan International Standard)

                    - JIS G 3141 SPCC SD (Japan International Standard)

                    - ASTM A 500 Grade A (American Standard)

                    - BS 1387 ( British Standard)

 

Steel vs Aluminum

Why use Steel instead of Aluminum?

First, steel is stronger than aluminum for the same size and thickness. In order for aluminum alloys to be at least the same strength as steel, it has to be at least double the thickness (steel 4mm = aluminum 8mm). When that happens, weight saving is not so apparent anymore. Of course there are also exotic materials and alloys that can match the strengths of steel, but the cost are astronomically high and therefore not very cost effective to bring into mass production.

Strut Bars and Chassis Strengthening Technology

If you're serious about your car's handling performance, you will first be looking at lowering the suspension. In most cases, unless you're a complete petrolhead, this will be more than adequate. However, if you are a keen driver, you will be able to get far better handling out of your car by fitting a couple of other accessories to it. The first thing you should look at is a strut brace. When you corner, the whole car's chassis is twisting slightly. In the front (and perhaps at the back, but not so often) the suspension pillars will be moving relative to each other because there's no direct physical link between them. They are connected via the car body, which can flex depending on its stiffness. A strut brace bolts across the top of the engine to the tops of the two suspension posts and makes that direct physical contact. The result is that the whole front suspension setup becomes a lot more rigid and there will be virtually no movement relative to each side. In effect, you're adding the fourth side to the open box created by the subframe and the two suspension pillars.

Is there a need to have our vehicle chassis strengthened?

The chassis of the car is the part which experiences the most of the abuse from the driver. It is particularly due to the weight transfer of the vehicle body during fast cornering, hard braking or hard acceleration. In some instances, the weight transfer during cornering may cause one side of the vehicle to experience as much as 3 times more force than the other side of the vehicle, causing enormous chassis flex/ vehicle body deformity and twist, consequently causing tires to lose grip. Deformity and twisting of the vehicle chassis during cornering may cause negative handling traits such as understeering and oversteering.

What is Chassis Flex?

With a strengthened chassis, the vehicle will react better to tuning changes. The improvement is particularly obvious over a hard suspension setting. The chassis is also able to cope better after the engine upgrades and Braking System upgrades. A strengthened chassis, by Chassis Strengthening Technology, will also protect the vehicle platform to allow it to last longer under hostile conditions, especially for monocoque vehicle platform.

FRONT STRUT BARS

Mounted at the front chassis for strengthening purposes. To eliminate all the suspension noise and more stability during acceleration, hard driving and braking ( simulating race track conditions ).

Every vehicle’s front chassis is different therefore designs and develops the front bars based on the actual conditions of the vehicle, repeatedly testing and proving to its perfection. High attention is taken during the design and development stage to ensure the chassis is able to withstand the load when a bar is being installed.

Ultra Racing is proud to bring to you the first of its kind in the country, the MULTI-POINT Front Strut Bar. The Front Strut Bar is installed to minimize the weight transfer of the vehicle body, therefore the vehicle will not loose traction easily during cornering.

LOWER ARM BAR

The Ultra Racing Lower Arm Bar is designed to reduce the flex of the vehicle chassis where it is connected by the Lower wishbone of the suspension system, thus to lessen the distortion of the vehicle lower suspension when it is under load, especially during hard cornering. It is installed at the lower mounting points between the left and right suspension and the vehicle chassis. Tremendously improving the stiffness at the area where the lower arm is connected to the vehicle chassis. The Ultra Racing Lower Arm Bar also keeps camber accurate during hard cornering.

REAR STRUT BAR & REAR UPPER BAR

Mounted at rear section of the car chassis (boot). Similar to the function of the front strut bar. The rear strut bar is use to support the rear section of the chassis, so that the force generated during hard braking and driving can be reduced.

The Rear Strut Bar is particularly useful for an FF vehicle. The Understeer behavior can be corrected by stiffening the rear chassis by installing a Rear Bar.

High attention is taken during the design and development stage to ensure the rear chassis is reinforced and strengthened in a proper way that it will not cause the vehicle body to undergo too much stress.

Rear Upper Bars is designed for vehicles with high roof and high CG (Centre of Gravity) such as MPV's, mini MPV's, SUV's and Hatch Backs.

Initially, Rear Upper Bar is invented specially for the 5 Doors Hatch Back cars. The 5 Door Hatch Back cars have weaker rear upper body due to their wide opening rear door. Under extensive investigation and actual road proving, it corrected the shortcoming of the vehicle’s swaying rear upper body.

SIDE FENDER BAR

Installed at the left and right side of the vehicle wheel arch or fender. Fender bars can give extra support and strength to the chassis especially during cornering.

As most of the vehicle’s front chassis over hanging is designated to carry the vertical loads from the front suspensions, it is vital that this part of the chassis is strong enough to take the bounce and rebound force of the suspension. Else, the effort of a good suspension will lose its meaning if the chassis absorbs all the forces from the suspension and not letting the suspension does what it suppose to do.

Therefore, these high quality 3-Point Fender Bars strengthen and reinforce these essential areas of your car and help maintain the suspension in position from all kind of vertical loads.

As a matter of fact, Fender Bars come as a standard feature on most of the high performance vehicles such as MITSUBISHI EVO and SUBARU WRX. Now, you can have the same feature on your car too!

Advantages of the fender bar:

  • Improve handling, stability at high speed and cornering, hence safer driving.

  • Provide a better braking and stopping performance.

  • Reduce NVH (Noise, Vibration and Harshness).

  • Increase stiffness of vehicle front chassis.

ANTI-ROLL BAR / SWAY BAR

Anti Roll Bars (also known as anti-sway bars, sway bars or lower tie bars) affect the handling of the car on the lower end of the suspension. Sway bars tie the lower suspension components together across the front or back, and affect a car's over steer and under steer. Sway bars will keep your car flat in turns instead of leaning over to one side. They distribute energy from the side of the car with all the force from the turn on it to the other side of the car, bringing the whole car down flat instead of leaning to one side. Of course the car will still lean some, but not as much. Sway bars provide better cornering especially at high speeds and work very well in conjunction with strut tower bars. However, they can have an adverse affect in off-road situations by leaving one tire completely off the ground.

To view animations on how UltraRacing will improve your vehicle's handling please go to http://ultraracing.my/v1/?page_id=2267

NOTE:This product is not suitable if there is salt content in the environment; which the vehicle operates in.